BP35-005 thru bp35-10 page: 1 frontier electronics corp. 667 e. cochran street, simi valley, ca 93065 tel: (805) 522-9998 fax: (805) 522-9989 e-mail: frontiersales@frontierusa.com web: http://www.frontierusa.com 35a high current silicon bridge rectifiers BP35-005 thru bp35-10 features z current rating 35a z reverse voltage rating up to 1000v z typical ir less than 1 a z high temperature soldering guaranteed: 260 c /10 second mechanical data z case: metal heat sink ca se, electrically insulated z terminals: universal .25? (6.3mm) fast on dimensions in inches and (millimeters) z mounting method: bolt down on heat sink with silicon thermal compound between bridge and mounting surface for maximum heat transfer efficiency z weight: 20 grams maximum ratings and electrical c haracteristics, ratings at 25 c ambient temperature unless otherwise specified single phase, half wave, 60 hz, resistive or inductive load. for capacitive load, derate current by 20% ratings symbol BP35-005 bp35-01 bp35- 02 bp35-04 bp35-06 bp35-08 bp35-10 units maximum recurrent peak reverse voltage v rrm 50 100 200 400 600 800 1000 v maximum rms voltage v rms 35 70 140 280 420 560 700 v maximum dc blocking voltage v dc 50 100 200 400 600 800 1000 v maximum average forward rectified output current at tc=55 c i o 35.0 a peak forward surge current single sine-wave superimposed on rated load i fsm 400 a storage temperature range t stg - 55 to + 175 c operating temperature range t op - 55 to + 175 c electrical characteristics (a t t a =25 c unless otherwise noted) characteristics symbol BP35-005 bp35-01 bp35-02 bp35-04 bp35-06 bp35-08 bp35-10 units maximum instantaneous forward voltage per bridge element at specified current v f 1.1 v maximum reverse dc current at rate dc blocking voltage per element i r 10 a note: suffix no. versus different cases and terminals dim min max remark h* 0.295(7.5) 0.311(7.9) suffix ?s? thin case i* 0.74(18.80) 0.84(21.30) suffix ?s? thin case l* 1.09(27.89) - suffix ?s? thin case case sufix no terminal normal metal case thin metal case normal plastic case aluminum base thin plastic case aluminum base fast on terminals no suffix s p ps wire lead terminals w ws pw pws in line pin configuration l ls 1.13(28.7) 1.12(28.4) 0.469(11.90) 0.429(10.90) 0.752(19.10) 0.673(17.10) l* 1.200 (30.5) min 0.042(1.07) 0.038(0.97) h* 0.442(11.23) 0.432 ( 10.97 ) 0.094 (2.4) diam i* 1.00(25.40) 0.90(22.86) 0.25 (6.35) 0.565(14.35) 0.525(13.35) 1.13(28.7) 1.12(28.4) 0.657(16.7) 0.618(15.7) 0.652 (16.6) 0.728(18.5) 0.689 ( 17.5 ) hole for no.10 screw 0.2 (5.08)diam. h* 0.442(11.23) 0.432(10.97) hole for no.10 screw 0.2 (5.08)diam.
BP35-005 thru bp35-10 page: 2 ratings and characteristic curves BP35-005 thru bp35-10 fig. 2 - typical reverse characteristics at t j =25 10 1.0 0.1 .01 instantaneous reverse current, microamperes 0 20 40 60 80 100 120 140 percent or rated peak reverse voltage t j = 175 300us pulse width 1% duty cycle 1 1.5 2 3 4 5 6 7 8910 15 20 30 40 50 70100 fig. 5 - typical junction capacitance per bridge element 500 400 300 250 200 150 100 60 capacitance, c.j. pf reverse voltage, volts t j =25 f=1mh z vsig=50m vp-p bp35-l in line pin configuration (plastic case) fig. 1 -maximum output rectified current average forward output current, amperes 20 40 60 80 100 120 140 160 180 case temperature t c without heat sink with (400mm 2 1.5mm) copper 35 30 25 20 15 10 5 0 ac 11.23 .432 10.97 .140 3.6 .120 3.05 .040 28.7 1.12 13.9
|
